Truck repair Truck electrical repair and diagnostics

Truck lights, gauges or wiring acting up?

Nexgen traces and repairs electrical faults on commercial trucks that still run: lights out, gauges or the dash dead or erratic, fuses that keep blowing, chafed or corroded wiring, failed relays and faults that come and go. Many can be traced and repaired where the truck is parked, if it is safe to work there. If you smell burning electrics or see smoke, pull over and shut the engine off; otherwise note when the fault shows and call.

Can I keep driving with an electrical problem?

It depends what has failed. A burning smell, smoke or a fuse that blows again straight away means stop: a short can start a fire. Headlights, brake lights, signals or wipers out mean the truck may not be roadworthy in the conditions you need them. A charging warning means the truck is running on its batteries and may stall when they are flat. A single marker light out in daylight, or one gauge misbehaving with everything else normal, may let you reach a safe place to have it looked at.

Seven-way connector and trailer cord Example

Example: one circuit runs from the cab to the trailer lights through the seven-way; a corroded pin or a chafed cord is a common place for lights to go out.

Call the nearest location.

Call now (204) 960-5390

Injury, fire or danger: call 911 first. We take calls 24/7.

Problems we commonly inspect

Burning smell or smoke from the dash or wiring
Hot insulation has a sharp, acrid smell: an overloaded circuit or a short, and a fire risk.
A fuse that blows again as soon as it is replaced
Something on that circuit is shorting to ground, often a harness rubbed through on the frame or a bracket.
Lights out, dim or flickering
Headlights, clearance and marker lights, signals or brake lights: a lamp, a switch, a ground or the wiring between them.
Gauges or the whole dash dead or jumping
A cluster that drops out at once suggests its power or ground; a single gauge suggests its sender or that one circuit.
Battery light or low voltmeter while driving
The engine runs but the charging system is not keeping up: the alternator, its belt or the charging wiring.
A fault that comes and goes
Fine in the yard, fails over bumps, in rain or after a wash: usually a loose connection, a chafed harness or water in a connector.
Accessories not working
Wipers, blower fan, horn, mirror heat or power outlets: a fuse, relay, switch or the motor itself.

Stop driving, or can it wait?

Stop and get help

  • A burning or hot-plastic smell, smoke, or heat from the dash, a switch or the wiring.
  • Headlights, brake lights or turn signals out when you need them.
  • Wipers or defrost failing in rain or snow.
  • The charging warning on and the voltmeter falling.
  • A fuse that blows again the moment it is replaced.

May be safe to assess further

  • A single marker or clearance light out in daylight.
  • One gauge erratic while the others read normally and no warning lamps are on.
  • An accessory that has quit with no smell, heat or other symptom.

Continuing to operate may risk further damage or create a safety issue. When in doubt, stop where it is safe and call. Injury, fire or immediate danger: call 911 first.

What to do right now

  1. If you smell burning electrics or see smoke, pull over where it is safe, shut the engine off and get out of the cab. If there is fire or anyone is hurt, call 911.
  2. Work out whether the fault is one item, a group of items or the whole truck: it tells the technician where to start.
  3. Note when it happens: over bumps, with the lights or heater on, in the wet, after a wash, or only when the truck is hot or cold.
  4. If the charging warning comes on, switch off loads you do not need and stop somewhere safe before the batteries run flat.

What not to do

  • Do not fit a larger fuse to stop one from blowing.
  • Do not tape over a smoking or melted wire and drive on.
  • Do not keep driving on the charging warning until the truck stalls.
  • Do not tap new accessories into existing circuits; many electrical faults start there.
  • Do not pull or flex harnesses near the belts and fan while the engine is running.

When you call, have ready

  • What has stopped working, and whether it is one item, several, or the whole truck.
  • When the fault shows: all the time, over bumps, in the wet, with certain switches on, or only hot or cold.
  • Any fuse that has blown, and the circuit it feeds.
  • Any smell, smoke, heat or melted insulation you noticed, and where.
  • Recent work: added lights, a radio, an inverter, a CB, a GPS unit, a new trailer plug, or body work near the wiring.
  • Where the truck can be parked off the road with the engine able to run for testing.

Not sure exactly where you are?

Your phone can find the spot and write the text for you.

Your position

Open in Maps

What a pin cannot say

Your text

Uses this phone’s location. Nothing is sent: copy it to paste in a message or read it out when you call.

What we check

Depending on the symptoms, the technician may check:

  • Battery and main ground connections, and the engine-to-frame and cab ground straps
  • Fuses, fusible links, circuit breakers and relays in the power distribution panels
  • Harness routing for chafing, pinching, heat damage and missing clips along the frame and through bulkheads
  • Connectors for corrosion, water entry and bent or backed-out pins
  • Lighting circuits: headlights, clearance and marker lights, signals, brake lights and their switches
  • Instrument cluster power and grounds, and the senders behind individual gauges
  • Alternator output and charging wiring with the engine running and loads switched on
  • Voltage drop across circuits that fail intermittently
  • Aftermarket wiring for inverters, radios, lights and other add-ons

Common causes

Possibilities, not a diagnosis of your unit:

  • A harness rubbed through on the frame, a bracket or an engine component
  • Corroded connectors or grounds, often from road salt and wash water
  • A failed relay, switch or circuit breaker
  • Aftermarket wiring added without proper fusing or routing
  • A loose or corroded main ground, which can cause several unrelated faults at once
  • A failing alternator, voltage regulator or drive belt
  • Water inside a connector or lamp housing
  • Rodent damage on a truck that has been parked for a while

Roadside or shop?

Often done where the unit is

  • Lighting faults: lamps, sockets, switches and their wiring
  • Fuses, relays and circuit breakers
  • Chafed or corroded wiring and connectors that can be reached safely
  • Charging tests and many alternator replacements

Often better handled in a shop

  • Intermittent faults that need the truck tested over a longer period
  • Harness repairs behind the dash or deep in the engine bay
  • Faults where a component must come off to reach the wiring
  • Work on a truck that cannot be parked safely away from traffic

Every fault and every spot is different. Describe it on the call and we will tell you what can be done where the unit is.

How it works

  1. Find the pattern

    What fails, when, and what else is switched on: the details you give narrow the circuit before a meter is connected.

  2. Make it fail

    An intermittent fault is traced while it is happening, by loading the circuit or moving the harness until it drops out.

  3. Split the circuit

    Power, ground and voltage drop are measured section by section until the bad stretch of wire, connector or part is found.

  4. Repair and protect

    The chafe, corrosion or failed part is fixed, then the wiring is secured and sealed so it does not wear through again.

  5. Prove it

    The circuit is retested under load, and with the engine running for any charging fault.

Where we work: Winnipeg, Highway 1 and Brandon

A truck with lights failing is hard to see on the Trans-Canada Highway (Highway 1) after dark. Around Brandon, Headingley and Winnipeg, take the next safe place to get fully off the road and tell us which lights still work.

Roadside assistance and mobile truck and trailer repair 24/7 along the Trans-Canada Highway (Highway 1) between Winnipeg and Brandon, in both directions: Headingley, St. François Xavier, Elie, Oakville, Portage la Prairie, MacGregor, Austin, Sidney, Carberry and Douglas, and the yards and roads around them.

Questions

Why does the same fuse keep blowing?
Something on that circuit is drawing too much current, usually a short to ground. A wire rubbed through against the frame is common. A bigger fuse does not fix it; it moves the failure to the wire, which can start a fire.
Why do my truck's gauges jump around or go dead?
Often a bad power or ground feed to the instrument cluster. If every gauge drops out together, the cluster supply is the first suspect; if only one misbehaves, its sender or wiring is more likely. On many trucks the gauges read engine data, so a communication fault can do it too.
The battery light came on while driving. What does it mean?
The charging system is not keeping up and the truck is running on its batteries. Switch off what you can spare and stop somewhere safe before they run flat. A belt, the alternator or the charging wiring are the usual suspects.
Can an electrical fault that comes and goes be found?
Usually, with the right details. When it happens, what was switched on and what the weather was all narrow the search. Some intermittent faults are better traced in a shop, where the truck can be tested for longer.