Truck repair Wheel seal, hub and wheel-end repair

Leaking wheel seal or a hot hub?

Nexgen repairs truck and trailer wheel ends: leaking wheel seals, worn or failing wheel bearings, damaged hubs and hubcaps, and the brake parts that oil or grease has reached. Many seal and bearing jobs can be done where the unit is parked when the wheel end can be worked on safely. If a wheel end is smoking, smells hot or is grinding, stop where it is safe, keep clear of it and call.

Can I keep driving with a leaking wheel seal?

Not far, and not at all if the wheel end is smoking, smells hot or makes noise. A leaking seal lets the oil or grease out and lets water and grit in. Once the lubricant is low the bearings run dry and heat up, which can seize the wheel, damage the spindle or start a wheel-end fire, and oil thrown onto the brake linings weakens the brakes on that wheel. A fresh seep with oil still showing in the sight glass and no smell or noise can usually be checked and booked in soon; an empty sight glass, oil streaming across the wheel, smoke or grinding means stop and call.

Hub and wheel seal, oil level and heat Example

Example: a hub running hot behind the drum; a wheel seal that is weeping lets the oil out and the heat in, and the bearing follows.

Call the nearest location.

Call now (204) 960-5390

Injury, fire or danger: call 911 first. We take calls 24/7.

Problems we commonly inspect

Oil or grease on the inside of the wheel
A wet ring or streaks thrown outward from the hub, often with grime stuck to it and sometimes reaching the tire.
Hubcap sight glass empty, cloudy or milky
No oil showing means it has leaked out; milky oil usually means water has got into the hub.
One hub hotter than the others
Noticed as a hot-oil smell at a stop, or as a much higher reading on an infrared thermometer than the other wheel ends.
Smoke from a wheel end
Oil or grease burning on a hot hub or drum: the stage before a wheel-end fire.
Growling, rumbling or grinding from one wheel
Noise that rises with road speed rather than engine speed, often worse in a turn.
Weak braking or a pull on one side
Oil or grease from a seal has reached the brake linings on that wheel.

Stop driving, or can it wait?

Stop and get help

  • Smoke, flame, or a smell of hot oil or burning from a wheel end.
  • Grinding, growling or squealing from one wheel that is getting louder.
  • A wheel that wobbles, or a tire that suddenly leans in or out at the top.
  • The sight glass is empty and oil is thrown across the wheel and tire.
  • The truck pulls under braking after oil appeared on a wheel.

May be safe to assess further

  • A light film at the seal with oil still showing in the sight glass, no smell and no noise.
  • A cloudy sight glass found at a pre-trip on a unit that has been parked.

Continuing to operate may risk further damage or create a safety issue. When in doubt, stop where it is safe and call. Injury, fire or immediate danger: call 911 first.

What to do right now

  1. If you see smoke from a wheel or smell hot oil or burning, slow down and stop at the nearest safe place, clear of fuel islands and dry grass.
  2. Keep clear of a smoking or hot wheel end. Do not touch the hub, hubcap or wheel, and do not open the hubcap or fill plug.
  3. If there are flames, get everyone away from the unit and call 911 first.
  4. From a safe spot, note which wheel it is and what you see: oil, smoke, the sight glass level. A photo helps.
  5. Call and describe the wheel position, the smell or noise, and how far you have driven since you noticed it.

What not to do

  • Do not touch a hub, hubcap or wheel to check how hot it is.
  • Do not open the hubcap or fill plug on a hot wheel end; hot oil can spray out.
  • Do not top up the hub oil and carry on without finding why it was low.
  • Do not keep driving to get home with smoke, noise or an empty sight glass.
  • Do not wipe oil off the brake side and treat it as fixed; soaked linings stay contaminated.

When you call, have ready

  • Which wheel end: steer, drive or trailer; which axle on a tandem or tridem; left or right side.
  • What you see: where the oil or grease is, and whether the sight glass is full, low, empty or milky.
  • What you hear or feel: noise that changes with speed, a vibration, or a pull when braking.
  • Whether the hub runs in oil (a clear sight-glass cap) or grease (a solid cap), if you know.
  • An infrared thermometer reading against the other wheel ends, if one is on hand. Never touch a hub to feel for heat.
  • Any recent brake job, seal replacement or hub work on that axle, and the axle make from its tag if it is visible.
  • Where the unit is parked, and whether it is on firm, level ground away from traffic.

Not sure exactly where you are?

Your phone can find the spot and write the text for you.

Your position

Open in Maps

What a pin cannot say

Your text

Uses this phone’s location. Nothing is sent: copy it to paste in a message or read it out when you call.

What we check

Depending on the symptoms, the technician may check:

  • The wheel seal and seal surface, and the lubricant level and condition in the hub
  • Wheel bearings and races for wear, pitting and heat damage, and bearing end play
  • The spindle for scoring or heat discolouration where the bearings and seal sit
  • Hubcap, gasket, sight glass, vent and fill plug
  • The axle nut and its locking system
  • Brake linings, drums and rotors for oil or grease contamination and heat
  • The ABS tone ring and wheel speed sensor, which bearing play can upset
  • On drive axles, the axle shaft flange gasket and the axle oil level, which can look like a seal leak

Common causes

Possibilities, not a diagnosis of your unit:

  • A worn, hardened or incorrectly installed wheel seal
  • Bearing end play out of adjustment, letting the hub move and the seal lose contact
  • Low or contaminated lubricant, including water that got in past a cap or vent
  • A blocked hub vent letting pressure build and push oil past the seal
  • Heat from a dragging brake hardening the seal
  • A grooved seal surface on the spindle or hub
  • A cracked hubcap, a damaged sight glass or a loose cap

Roadside or shop?

Often done where the unit is

  • Many wheel seal and bearing replacements, when the unit is parked on firm, level ground clear of traffic
  • Replacing a damaged hubcap, gasket, sight glass or vent and refilling the hub
  • Checking a wheel end to decide whether the unit can be moved and how far

Often better handled in a shop

  • A spindle that is scored, worn or heat-damaged
  • A wheel end after a seized bearing or a fire
  • Several wheel ends at once, or a seal job that grows into brake work across the axle
  • Any wheel end on a shoulder too narrow to work on safely

Every fault and every spot is different. Describe it on the call and we will tell you what can be done where the unit is.

How it works

  1. Call, or send your location

    Call the location nearest the unit, or text a map pin with the unit number, then call.

  2. Describe the truck, trailer and problem

    What you see, hear and smell, the warning lights or codes, and whether the unit is loaded.

  3. We assess it with you

    From what you describe, and again when the technician reaches the unit: what is wrong, and whether it can be repaired where it stands.

  4. Repair where the unit is, when it is appropriate

    When the fault and the spot allow it to be done safely and properly.

  5. A shop or further work, when it is needed

    When it cannot be done on site, we tell you why and what the next step is.

Where we work: Winnipeg, Highway 1 and Brandon

If a wheel end starts to smell or smoke on the Trans-Canada Highway (Highway 1), take the next safe place to stop rather than pushing on to Brandon, Headingley or Winnipeg. Tell us your direction and the last exit you passed.

Roadside assistance and mobile truck and trailer repair 24/7 along the Trans-Canada Highway (Highway 1) between Winnipeg and Brandon, in both directions: Headingley, St. François Xavier, Elie, Oakville, Portage la Prairie, MacGregor, Austin, Sidney, Carberry and Douglas, and the yards and roads around them.

Questions

How can I tell if a wheel seal is leaking?
Look for oil or grease on the inside of the wheel and tire. A leaking seal throws lubricant outward from the hub in a ring or streaks, and dirt sticks to it. On an oil-bath hub, a sight glass that is low or empty confirms it. Look from a safe spot and do not open the cap.
What does a milky sight glass mean?
Usually water has got into the hub oil. It can come in past a damaged seal, a loose or cracked cap or a vent. Water-laden oil does not protect the bearings, so the hub needs draining, the leak path found and the bearings inspected.
Can a wheel seal be replaced on site?
Often, when the unit is parked where the wheel end can be worked on safely. A seal and bearing job needs firm, level ground clear of traffic. A damaged spindle or a wheel end that has overheated badly is often better handled in a shop.
Why does a seal leak affect my brakes?
Because the oil or grease ends up on the brake linings. Contaminated linings grip less and unevenly, which can cause a pull. They usually need replacing, not cleaning, so the seal job may include brake parts on that wheel.
Can a hot hub start a fire?
Yes. A dry or failing bearing can heat the hub enough to ignite the grease, oil or the tire. That is why smoke or a hot smell from a wheel end means stop, keep clear and call, and flames mean call 911 first.